TheDraw for example, the tool that I was using for most of my ANSIs and ASCIIs is limited to 100 lines. DOS ASCII editors also have limitations in the length of an ASCII (or ANSI) that can be worked on at once. DOS adds automatically a prompt to continue with the "next page", if your ASCII is taller than 23 lines. DOS was showing 25 lines at once on the screen. There is no real limit for the height of an ASCII. Only 79 characters of the 80 are usable, because if you use the full 80 characters, DOS added automatically a line-break, causing effectively an empty line after which the next line of your ASCII will continue. This limitation has its roots in MS DOS as well, where the screen width in text mode was limited to 80 characters in width. Traditional ASCII's are limited to 79 usable characters in width. Top/Bottom Single Line, Left/Right Double Line Border CharactersīOX DRAWINGS VERTICAL DOUBLE AND LEFT SINGLEīOX DRAWINGS VERTICAL DOUBLE AND RIGHT SINGLEīOX DRAWINGS UP DOUBLE AND HORIZONTAL SINGLEīOX DRAWINGS DOWN DOUBLE AND HORIZONTAL SINGLEīOX DRAWINGS DOWN DOUBLE AND RIGHT SINGLEīOX DRAWINGS VERTICAL DOUBLE AND HORIZONTAL SINGLE Top/Bottom Double Line, Left/Right Single Line Border CharactersīOX DRAWINGS VERTICAL SINGLE AND LEFT DOUBLEīOX DRAWINGS VERTICAL SINGLE AND RIGHT DOUBLEīOX DRAWINGS UP SINGLE AND HORIZONTAL DOUBLEīOX DRAWINGS DOWN SINGLE AND HORIZONTAL DOUBLEīOX DRAWINGS DOWN SINGLE AND RIGHT DOUBLEīOX DRAWINGS VERTICAL SINGLE AND HORIZONTAL DOUBLE High ASCII Characters TableīOX DRAWINGS LIGHT VERTICAL AND HORIZONTALīOX DRAWINGS DOUBLE VERTICAL AND HORIZONTAL For example the character with ASCII code 245 would be this one ⌡, if the user is using Code (typically used in North America), however, the same code 245 would produce this character § on a computer, which uses Code (typically used in Western Europe, including Germany).īecause of those subtle differences in extended character sets, I suggest to stick to the basics, which work across the board, the standard US-ASCII characters, the block characters and the single and double line border character sets. The only problem with the non-graphical characters in MS DOS is that they could be different depending on the "Code Page" used (language specific character sets) by the user. basically any additional character of the "upper half" of the extended characterset beyond the "first half" (128) (ASCII Standard characters and system control characters) could be utilized. Top/Bottom Single Line, Left/Right Double Line Border: ╢ ╖ ╜ ╟ ╨ ╥ ╙ ╓ ╫Īdditional High ASCII Characters that could be used* ![]() ![]() Top/Bottom Double Line, Left/Right Single Line Border: ╡ ╕ ╛ ╞ ╧ ╤ ╘ ╒ ╪ Single Line Border: │ ┤ ┐ └ ┴ ┬ ├ ─ ┼ ┘ ┌ĭouble Line Border: ╣ ║ ╗ ╝ ╚ ╔ ╩ ╦ ╠ ═ ╬Īdditional Border Character Sets for users with CP437 (North America), which is not available in all other Code Pages, such as CP850 (Western Europe). The Block Set Characters: ░ ▒ ▓ █ ▀ ▄ ▌ ▐ ■ ▪ Border Character Sets The alternative term "Block ASCII" is derived from the fact that most "High ASCIIs" make use of the characters that look like blocks in 2D (from the side). The non-standard, MS DOS specific characters start afterwards with a "higher" number in the ASCII Table, hence "High-ASCII". The Characters 0-127 are used for the standard ASCII characters. The DOS ASCII Table contains 256 characters. The name "High" in "High ASCII" is derived from the location of the character codes in the ASCII Table. To learn about the difference between the extended MS DOS character set and the standard ASCII format, check out my other article about the The term "Block ASCII" or "High ASCII" refers to text art that utilizes the the Microsoft DOS proprietary extended ASCII character set. I am sorry for not being able to finish it yet |. However, even in its incomplete state, it might provide some value insights and tips for one or the other reader already. It is incomplete and to be considered "Work in Progress". ![]() For (int y = 0 y < settings.Please Note: This guide was is being written by Carsten Cumbrowski aka Roy/SAC since August 2009.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |